|
|
Place mouse over 'Training' menu above to display extra options |
Page Location: Home > Training > Information Sheets > #27 PG-11 Video [NTSC Japanese format] |
|
|||
|
|||
|
|||
|
PG-11 Video - NTSC Japanese Format
A copy of the NTSC video for PG-11 may have been available in initial PG-11 Kits sold in Australia, however this video is no longer available.
The following is a guide to the translation/ understanding of the Video enclosed in the PG-11 kit. Viewing this video helps to graphically show the process of printing, what goes where etc. Where possible use the counter guides provided to keep track of visuals and explanations.
Insert PG-11 video and begin playing.
The counter on your VCR should be re-set to zero on the introduction of the PG-11 logo at the commencement of the video.
Three beeps sound as the PG-11 squares appear reset to ZERO at the twinkle sound and the wording appears. (The beeps will act as a count in)
Start - 0 min 00 sec
The PG-11 Video Contents
PG-11 Japanese Instruction Manual This manual replaces the Japanese version.
Part 1 - PG-11 Kit Outline
1 min 00 sec
PG-11 Machine
NB: Protective plastic on Registration Plate.
Open Battery Cover and insert batteries (provided in kit) replace when done.
Stage Glass A unique feature, Master Guides at top and bottom, Master Holders at left and right.
Registration Plate remove by pulling out close to hinge.
Note - Plastic cover must be removed before printing.
Pad Table remove plastic cover before printing.
Paper Guide
Alignment Guides and Alignment Pegs
Imaging Pegs
Lamp Housing
4 min 00 sec
Other Contents
Artwork Book, Printing Paper & Artwork Pen.
PG B6 HM Print Master (Pack 5), Print Lamps (Pack 10) & Blue Filter.
Printing Inks (Black, Blue, Red, Green, Brown, Yellow & White), Process Colours (Cyan, Magenta & Process Yellow) & RISO OK Cleaner (15ml).
Ink Blocking, Card Racks (Pack 2) & Printing Post Card.
Ink Pallet & Pallet Knife.
PRINT GOCCO HANDBOOK & Instruction Manual Not available in this version of the PG-11.
5 min 07 sec
Part 2 Printing with PG-11
Section 1 Selecting your artwork
Select your design from the book
Cut out the design.
With carbon pen write in additional information ie name/ address/ etc
Ideal size is 140mm x x90mm & Other artwork examples
6 min 27 sec
Section 2 Imaging the Print Master
Remove the plastic cover from the Pad Table.
Center Alignment Guides to the Home position.
Insert Print Master from right to left under Master Guides.
Insert Card onto pad use paper guide where possible to ensure correct registration of each print.
Place artwork onto card ready for imaging.
7 min 52 sec
Remove Print Lamps from pack and place into Lamp Housing.
Insert Lamp Housing into PG-11 machine slide in rear first ensuring the alignment marks are correct as indicated.
8 min 40 sec
Place hands on front corners and press down to image screen.
Use caution there is nothing else in the machine that may effect toe hinge movement.
Remove Lamp Housing CAUTION Print Lamps will be hot.
When cool remove lamps CAUTION Print Lamps can be crushed when exposed.
Open PG-11 machine and remove Print Master
9 min 50 sec
Section 3 Inking the Print master
Select your desired colours.
Lift back plastic cover from Print Master.
Place Ink Blocking around design area.
Ink Print Master with desired colours Use PRINT GOCCO Hi Mesh Ink only.
Once inked replace plastic cover.
11 min 10 sec
Section 4 Printing with PG-11
Open PG-11 and replace Print Master.
Gently remove artwork from Print Master.
Ensure Pad Table is in Home position.
Print first print.
Once printed, view the design and check ink coverage/ etc.
Place cards into Card Racks to dry.
13 min 16 sec
Part 3 Multi-Plate Printing
PG-11 is the perfect machine for multi-plate printing due to its fine detail registration ability.
13 min 55 sec
Section 1 Selecting your Artwork
Select your design from the book
Cut out the design.
With carbon pen write in additional information ie name/ address/ etc
You will have 3 separate pieces of artwork.
Center Alignment Guides to the Home position.
14 min 20 sec
Section 2 Imaging your Print Master
Insert B6 HM Print Master and 1st piece of artwork.
Insert Lamp Housing CAUTION insert correctly
Flash design and remove Lamp Housing.
Remove the Print Lamps from the Lamp Housing CAUTION Print Lamps will be hot
Repeat for the 2nd & 3rd pieces of artwork.
15 min 40 sec
Section 3 Inking the Print Master
Place Ink Blocking around design area and cover with ink.
To mix ink, use the pallet sheets & pallet knife supplied with the kit.
16 min 15 sec
Section 4 Printing with PG-11
Insert Print Master & remove artwork.
Place original artwork onto Pad Table
Peel off plastic cover from Registration Plate.
Insert the Registration Plate into the PG-11
Perform a standard print onto the Registration Plate.
Look through the Registration Plate if it is not aligned, loosen the Alignment Pegs and align the design tighten Alignment Pegs when finished.
Remove Registration Plate.
Clean with RISO OK Cleaner & tissue.
NB: You can clean the Registration Plate later if needed.
Remove the artwork from the Pad Table and place card/ paper onto the Pad Table.
Print design as normal.
Card Racks will hold the design and speed drying.
19 min 58 sec
Place 2nd Print Master into PG-11.
Lay the 1st print onto the Pad Table.
Insert Registration Plate and print.
Align the design as required.
Remove the Registration Plate and continue printing run for 2nd Print Master.
21 min 15 sec
As with the previous masters, insert the final Print Master and align the design using the 2nd printed copy for registration.
22 min 06 sec
Part 4 Full Colour Process Printing
Involves 3 pieces of artwork printed in the three colours Cyan, Magenta & Yellow.
1st print is Cyan
2nd print is Magenta
Sample of both colours together
3rd print IS Process Yellow
Final Result
Cut out the artwork & image your Print masters.
1st piece
2nd piece
3rd piece
24 min 00 sec
Print the Cyan copy first
When ready to print the second colour, insert the Registration Plate.
Print and align the design by adjusting the Pad Table tighten Alignment Pegs when finished.
Remove the Registration Plate and complete print run.
After completing this colour, again insert the Registration Plate, print and register the design.
This will finish your print run and provide you with a Full Colour print.
Once finished printing protect your Print Pad by inserting a blank card and lowering the lid.
26 min 10 sec
Part 5 Card Competition & RISO Details
Every PRINT GOCCO owner can enter the International Handmade Printed Works Competition (Card Competition). The competition is held annually with entries opening Mid October and closing Early January.
Keep a copy of ALL your designs printed and enter this great competition each year - The prizes are fantastic with individual winners selected for Australia as well as internationally.
27 min 35 sec
Part 6 PG Accessories
Ink colours available Standard, fluorescent, Pearl/ Metallic & Pastel.
Embossing powders (Japanese version) Also available from your Distributor.
PG Felt Sheet
Artwork Books (Japanese) Some books are available locally.
PG CD Masters NOT AVAILABLE OUTSIDE JAPAN
Stamp Kit for Cloth your fabric solution.
B5 HM Kit This version is no longer available, however a replacement model is already under production.
The End - 30 min 10 sec